檢測密封試驗  

油箱密封性試驗應在裝配完畢后進行。帶有可拆卸的散熱器或冷卻器時，可以在拆卸狀態下試驗，試驗用靜油柱法或靜氣壓法。

1.柱法
靜油柱試驗法是在變壓器儲抽柜的注油孔上加裝一根高度為0.6m以上的油管，在油管頂端焊裝一個貯油桶，以備變壓器油因熱脹冷縮或繞組內氣泡溢出作補充用，防止造成缺油。這樣經24h后觀察應無滲油現象。此方法一般用在160kVA以上的。

2.靜氣壓法
靜氣壓法是在箱蓋上或儲油柜上的通氣孔連接一個帶有氣壓表的管子，端部裝有旋塞，緩慢施以氣壓到0. 03MPa，然后將旋塞關閉，經24h觀察，油箱各處不得發現有滲漏現象。所有氣體(空氣或惰性氣體) 是干燥的。氣壓試驗時，應將儲油柜與油箱相連通，有 氣道的要將玻璃板換成鋼板密封。一般是將儲油柜上吸濕器拆去.接三通接頭.將氮?dú)馄恐械獨饨?jīng)降壓表閥降壓后通入儲抽柜或膠囊袋中，關閉閥門，觀壓壓力表12h不顯著降低。對密封式有波紋油箱的變壓器，應加0.025MPa壓力12h不滲漏。而按國家標準GBJ148-1990《變壓器驗收規范》規定，變壓器箱蓋上加0.03MPa24h變壓器本體不滲漏，有載分接開關加0.06MPa24h不滲漏。在做密封試臉前，有時要抽真空，它們單位的相互關系。

1nunHg = 133. 322Pa
lat(工程大氣壓)=0.0980665MPa≈0.1MPa
1mm(標準大氣壓)=0. 101325MPa

Tank seal test

Tank tightness test after assembly. Demolition state with a detachable radiator or cooler, you can test, test static oil column method or static pressure method.

A static oil column method
Static oil column test method is to install a height of 0.6m above the tubing on the filling hole of the transformer storage drawers, a jerry can in the tubing to the top welding to prepare for transformer oil bubble due to thermal expansion and contraction or winding overflow to supplement, to avoid creating short of oil. So that after 24h observation should be no oil leakage. This method is generally more than 160kVA transformer.

(2) static pressure method
Static pressure method is to connect the transformer cover or oil storage cabinet vent pipe with a barometer, the end is equipped with cocks, slow to impose pressure to 0. 03MPa, then cocks Close, observed after 24h, tank throughout not found to have leakage. Gas (air or inert gas) must be dry. Pressure test, the storage cabinet should be connected to the tank through secure airway to the glass replaced with steel plates sealed. Generally, oil storage cabinet dehumidifiers remove them. Pick the tee. Nitrogen bottle of nitrogen through the valve buck buck table access storage drawers or capsule bag, close the valve, the concept of pressure pressure gauge 12h was not significant reduced. 0.025MPa pressure 12h does not leak sealed corrugated tank transformer, should be added. And national standards GBJ148-1990 transformer acceptance of the provisions of the transformer cover plus 0.03MPa24h transformer body does not leak, OLTC to add 0.06MPa24h not leak. In sealed test face, and sometimes to the vacuum, the mutual relations of their units.
1nunHg = 133. 322Pa
of lat (works atm) = 0.0980665MPa ≈ 0.1MPa
1mm (standard atmospheric pressure) = 0. 101325MPa

中國●凱潛━━真誠到永遠！

重慶凱潛制造有限公司

銷售電話：023-65217597

手機：13452883096（24小時服務）

傳真：13350355997

網址：         

郵箱：308317328@qq.com <